Description
Solid Brass T-Bar Hardware with a French Vintage Line
A single hardware family for the whole room: round knobs for small doors, single-hole T pulls for cupboards, and two-hole bar pulls for wide drawers and paired wardrobe doors. All three share the same turned collars and flared bases, so the joinery reads as one considered scheme rather than a collection of parts.
Machined from Solid Brass
Each piece is machined from solid brass rather than formed from hollow sheet, then brushed and hand-finished. That gives the bar a reassuring solidity in the hand and a surface that wears into a deeper tone over the years instead of chipping down to a base metal.
The T-Bar Profile
A slim round bar with turned collars at each end sits on one or two stems. The shape gives fingers a natural place to fall and keeps the front of the cabinet visually quiet — enough presence to read as a detail, not so much that it competes with the door.
Three Mounting Styles
Choose by opening size: round knobs for narrow doors and small drawers, single-hole T pulls for standard cabinet doors, and two-hole bar pulls for wide drawers or pairs of wardrobe doors. Because the finish and profile repeat across all three, mixing them is the intended way to use the range.
Round Knobs — 25 mm & 30 mm
A stepped disc knob with a turned collar and a flared base. The 25 mm face suits compact drawers and cupboards; the 30 mm face gives a wider target on larger doors. Both mount through a single hole and sit close to the surface.
Single-Hole T Pulls — 70 mm & 80 mm
A centred T bar on one stem, fixed with a single screw. The 70 mm bar is proportioned for standard cabinet doors and slim drawers; the 80 mm bar gives a slightly longer grip for wider doors. Both are available in the finishes listed above.
Two-Hole Bar Pulls — 134 / 165 / 200 mm
Longer bars on two stems, for wide drawers and paired doors. Overall lengths are 134 mm, 165 mm and 200 mm, with hole centres at 64 mm, 96 mm and 128 mm respectively. Centre-to-centre spacing is what decides the fit, so check your existing holes before ordering.
Three Finishes
Natural Brass keeps the warm, lightly brushed original tone. Antique Brass is darkened and relieved on the high points for an aged, brown-brass patina. Polished Chrome is bright and cool, and suits grey, white and black joinery where warm metal would fight the palette.
Dimensions at a Glance
| Profile | Size | Mounting | Hole centers (CTC) |
|---|---|---|---|
| Round knob | Face Ø 25 mm, height 24 mm, base Ø 15 mm | Single hole | — |
| Round knob | Face Ø 30 mm, height 26 mm, base Ø 18 mm | Single hole | — |
| T pull | Length 70 mm, height 31 mm, bar Ø 11 mm, base Ø 21 mm | Single hole | — |
| T pull | Length 80 mm, height 31 mm, bar Ø 11 mm, base Ø 21 mm | Single hole | — |
| Bar pull | Length 134 mm, height 31 mm, bar Ø 11 mm, base Ø 21 mm | Two holes | 64 mm |
| Bar pull | Length 165 mm, height 31 mm, bar Ø 11 mm, base Ø 21 mm | Two holes | 96 mm |
| Bar pull | Length 200 mm, height 31 mm, bar Ø 11 mm, base Ø 21 mm | Two holes | 128 mm |
Choosing the Right Center-to-Center
For two-hole pulls, measure from the centre of one existing hole to the centre of the other. The 134 mm bar uses 64 mm centres, the 165 mm bar uses 96 mm, and the 200 mm bar uses 128 mm. If you are drilling fresh holes, mark both from the handle itself so the spacing matches exactly.
Easy Installation
Knobs and single-hole T pulls need one M5 × 25 mm screw through a standard door or drawer front. Two-hole bar pulls use two M5 × 25 mm screws at the stated centres. Slotted or Phillips heads both work; matching screws are included with every piece.
Care & Longevity
Wipe with a soft dry cloth and avoid abrasive cleaners or metal polish. Natural and antique brass darken gradually with handling, which is part of the finish rather than a fault. Keep the hardware dry and avoid prolonged contact with standing water.
What’s in the Box
One solid brass knob, T pull or bar pull in the selected size and finish, plus the matching mounting screws. Choose the size and finish from the options above to match the rest of your project.
