Description
Clear plastic furniture risers that lift a chair, table or sofa by 14–60 mm
These are screw-in furniture risers — a clear, rigid plastic foot with a metal wood screw set into the top. Screw one into each leg and the piece sits higher, while the clear body almost disappears against the floor. Use them to raise a low chair to a comfortable height, lift a sofa clear of a robot vacuum, level a table on an uneven floor, or keep a cabinet base off a damp floor. Each set contains four risers in one size, enough for a single chair or table.
Why clear rigid plastic, not soft rubber
- Rigid, not compressible — a solid plastic body holds its height under a furniture leg; a soft rubber pad would squash and the lift would disappear.
- Clear / frosted finish — blends with wood, tile and laminate instead of leaving a black rubber mark on the floor.
- Metal screw + brass washer — the screw is embedded in the plastic and backed by an internal brass washer, so the fixing is metal-on-metal.
- Non-marking base — the smooth plastic foot slides without scuffing and takes the rattle out of a loose leg.
- 22 sizes, two shapes — round (Ø18–50 mm top) and square (22–37 mm top), heights from 14 mm to 60 mm.
- Pack of 4 — four risers and four matching screws in one size.
Round or square?
Round risers suit turned or cylindrical legs and read as a neat circular foot. Square risers suit square-section legs, benches and cabinet corners, and give a little more contact area at the same top size. If you are unsure, measure the leg across its widest point and choose the riser whose top is the same or slightly larger.
How to choose your size
Pick by the two numbers in the name — top size × height:
- Top size — the diameter (round) or side length (square) of the plastic foot. Match it to the furniture leg so the leg sits fully on the riser.
- Height — how much lift you get. 14–21 mm is a subtle lift; 30–40 mm clears most robot vacuums; 50–60 mm gives a pronounced raise.
- Leg type — round legs pair with round risers; square legs, benches and cabinet corners pair with square risers.
See the full table below for every size.
Size (Top × Height) mm
| Shape | Top (mm) | Height (mm) | Set |
|---|---|---|---|
| Round | Ø18 | 14 | 4 |
| Round | Ø18 | 21 | 4 |
| Round | Ø18 | 35 | 4 |
| Round | Ø20 | 20 | 4 |
| Round | Ø20 | 28 | 4 |
| Round | Ø30 | 20 | 4 |
| Round | Ø30 | 30 | 4 |
| Round | Ø30 | 40 | 4 |
| Round | Ø30 | 50 | 4 |
| Round | Ø50 | 50 | 4 |
| Square | 22 | 18 | 4 |
| Square | 22 | 23 | 4 |
| Square | 22 | 27 | 4 |
| Square | 22 | 28 | 4 |
| Square | 22 | 32 | 4 |
| Square | 30 | 20 | 4 |
| Square | 30 | 30 | 4 |
| Square | 30 | 40 | 4 |
| Square | 30 | 50 | 4 |
| Square | 30 | 60 | 4 |
| Square | 37 | 30 | 4 |
| Square | 37 | 40 | 4 |
Where they work
Dining chairs and stools · Coffee tables and side tables · Sofas and armchairs · TV stands and media units · Cabinets and counters · Desks · Beds and bed frames · Classroom and folding furniture.
Installation
Drill a pilot hole slightly narrower than the screw, start the riser by hand, then tighten with a screwdriver until the top sits flush against the leg. No glue and no adhesive felt — and you can unscrew and move them later.
Specifications
Material: clear / translucent rigid plastic body with embedded metal wood screw and brass washer · Shapes: round, square · Top size: Ø18–50 mm (round), 22–37 mm (square) · Height: 14–60 mm · Set: 4 risers + 4 screws · Finish: clear / frosted · Installation: screw-in.
Care
Wipe with a damp cloth. The plastic is unaffected by normal indoor humidity; avoid prolonged standing water at the base. Check the screws are snug after the first week of use and re-tighten if a leg works loose.
Production & delivery
Stocked and shipped from our studio. Orders usually leave within 1–3 business days. Worldwide delivery available; duties calculated at checkout where applicable.
Need a larger quantity?
We supply furniture risers and glides in bulk. Ask about bulk pricing.
FAQ
- Will they scratch my floor? The base is smooth plastic and non-marking in normal use; check for grit before installing.
- Are these rubber? No — the body is rigid clear plastic with a metal screw. It will not compress like a rubber pad.
- Do I need to drill? Yes — a pilot hole helps the screw start cleanly and prevents splitting.
- Can I cut them down? No — the height is fixed by the moulded body; choose the height you need.
- How much load will they take? They are intended for everyday household furniture; spread the load across all four legs.
Why Bespora
Bespora Studio supplies furniture hardware direct from the workshop — consistent specs, honest materials, and volume pricing when you need it.
